I’m thinking about upgrading my W-Fi and I was curious what wireless access points (WAP) people are using. I’m currently using a Netgear R7800 running OpenWRT.
You must log in or register to comment.
Get yourself some old cisco 3600 re-flash it with standalone firmware and get enterprise class WAP for cheap.
EAP-615
In my opinion look much nicer in a home compared to ceiling mounts. I also run TP-Link Omada router and switches and selfhost the controller.
I have two TP-Link EAP610, one EAP245, and one EAP615-Wall. The Omada controller runs on my home server in an LXC. Three of the units are powered by PoE, and the garage one is meshed in. I needed three in my house because the walls have chicken wire in them which blocks and reflects WiFi. It took some trail and error to get the WAPs in suitable locations. The main one in the basement is under a wall, such that it has line of sight into 5 rooms of the house. I used iPerf to test performance at the edges of each room, until I could get at least 300 Mbit reliably. That was the only way I could ensure that I was getting a direct signal and not a reflection off a wall.
Went all in with UniFi some time back. No regrets.
Currently running a few U6s. No real motivation to upgrade to U7s.
+1 on this. Though i picked up 2 u7’s. VLAN support, easy to maintain and lets face it, superior function from most retail APs. If you’re a power user, this is the way.
I have one of the mikrotik hap things because it was cheap.
I have 2x Tplink EAP 610 access points. Linking back to an Opnsense virtualized router. The APs are great and Omada is fantastic - I’m running it in a docker container with no cloud access required.
I would go all Omada if I could but that would mean I’d need 3 POE Omada switches and I cant justify that cost at the moment.
Ruckus APs with wired backhaul OpnSense box runs the network.
Is Ruckus not crazy expensive? We used it for customers and they are like €500 an access point.
Used on eBay and flashed with the Unleashed firmware. It’s the same price range as Ubiquiti stuff.
I use the tp-link EAP615 wall Apps, they are great and run OpenWRT like a champ.
I use the Unifi access points. They work well and are fairly inexpensive. The management software can change settings on all of them at once, which is really handy if you have several.
It’s also really annoying if you only have one.
The AP works really well, so I put up with it.
Which ones do you have? Which ones would you get if you were buying now?
Not OP, I’ve installed a little bit of all of them for work, every form factor and version seem to be stellar.
I installed a bunch of Enterprise 7s at work and they’re super fast, but approaching chonky in size. Honestly, I really like the in-wall HDs They cover most of my house
The U6LR is amazing but overkill. I use one to cover the house and hdnano to mesh with a uap-ac in an external building.
I use a MoCo bridge and two U6LRs to cover 1km of farmland.
What do you think about the U7 Pro?
Pro has issues such as disconnects for 2.4ghz and runs hot.
If you’re looking for top radio performance, not necessarily the fastest speed, get the Pro models, older gen / second hand if needed, especially if you have suboptimal physical conditions. E.g. concrete walls, metal, etc. I had AC Lite, AC LR and AC Pro in use at some point. All of them were very good but the Pro had the best overall radio performance. If you’re in a wooden house with drywall partitions, probably all would do well enough.
I had a few AC Pros in a 110+ year old house where other AP’s had issues with all the plaster & lathe walls. They worked great. I also have a couple of them installed at a non-profit org I volunteer with and everybody is very happy with how they work there as well.
After moving from that first house to a new one with a bigger footprint I upgraded to a pair of their U6 mesh AP’s, one at each end of the house. Never had any issues with them.
Aaah, good old plaster wire mesh, it’s kinda like a Faraday cage. I’ve lived in a condo with plaster walls and one room that had it all around was nearly impenetrable.
Not OP, but I have one NanoHD upstairs, one IW-HD and one U6-IW. Basically bought them in that order when needed. The IW have the advantage to also act as Ethernet switch to a few devices like Apple TV and so on.
My access points are AC Lite and and U6 Lite. Those are discontinued though.
If I get more for inside, I would probably get the U6+. I am also thinking about getting one of the AC Mesh access points for outside. I’m not too worried about speed since anything that needs high speed is wired. I don’t have any neighbors, so I have all the bands to myself. If you are in an urban area, you should probably consider one with 6GHz support.
What are your thoughts on the U6+ vs U7 Pro? I’m not in an apartment so I probably don’t need 6 GHz? The U7 pro seems more modern and future proof, though but I do like the OpenWrt compatibility in case I don’t like stock firmware.
The U6+ will nearly max out gigabit with a 160MHz channel. The U7 Pro can provide higher speeds, but keep in mind there is only room for a single 240MHz channel on 5GHz. You will need 2.5G ethernet to take advantage of the higher speeds.
Interference from any other WiFi networks within your channel will slow things down a lot though. That makes running with channels wider than 80MHz difficult if there are any other networks in range.
Fritzbox boxes.
They tick all the checkboxes
- good standards support (including dect protocol if you want to have an ip phone or even iot protocols)
- fast wifi speeds
- cheap (at least for the second hand in ebay)
- super stable, never had a problem with them in 5 years or more
- fast roaming support out of the box
It is a well known brand in Germany but pretty unknown outside that country. Honestly it is the best bang for buck I was able to get.
Honestly, I would spend 10 minutes checking on them
I really like them but they do have two downsides for “more advanced” users (or at least for me) - it is a home device as after all.
- No support for VLAN or VLAN tagging - you can set up you WiFi and a guest WiFi. You can also map the guest network to an Ethernet port. But that’s about it.
- There is no way to change the DNS suffix (*. fritz.box) to another value - I do own a domain that I use for the local services on my home server, etc. which then allows for Let’s Encrypt certificates, but I cannot use it “out of the box”.
If you’re an advanced user, there’s plenty of ways around that, though. I just wished that these two thing were to exist in the firmware to have less work with my home infrastructure.
Totally agree with the first point, it is a limitation, and the guest wifi sticking to a eth port is just a patch. One that works but still a patch.
But I don’t see the point of the prefixes. What do you mean? I also have a custom domain and a local dns server y can use the domain even internally. I just simple ignore that…
Yeah, I’m also using a local resolver. But since I had some problems using another DHCP server (which was probably a problem on my end), so I’m current setting some devices in my FRITZ!box to a fixed IP and then enter that in my DNS server. If I could just skip the second part and tell the FRITZ!Box to just resolve printserver.example.com instead of printserver.fritz.box - that’d be nice. Maybe I should do another try with a DHCP server soon.
I’m using a couple of TP-Link EAP225 ceiling-mounted PoE access points, and one EAP235-wall wall-mounted one, connected to my old TP-Link Archer C7 router (with the antennas disabled) running OpenWRT.
I’d like to replace the router with something rack-mounted, but haven’t gotten around to it yet.
I purchases a few Netgear R6220, and of course flashed OpenWRT on all of them!
Great hardware, cheap, and perfectly supported. A few years old, so I could even find them used at an amazing price point.
I used to use R7800s. Then switched to UAP AC Pro / U6 Pro. Today just tested the OpenWrt One.
- The R7800 (on OpenWrt) is superb, fast, reliable. Can’t say anything bad about it. One of the most successful wireless platforms I’ve used. Probably the best implementation of this chipset too.
- The UAP AC Pro / U6 Pro perform better than the R7800. They have significantly better radio performance. The range is longer, coverage is uniform, performance is more consistent within the covered area. Adding a local Unifi controller (can be done in Docker) adds some nice wireless and management features like band steering. They don’t work well for bridging / mesh though. I had to run a bridge at some point and a set of Unifi had significant latency spikes, making it bad for gaming and other low-latency applications. A R7800-to-R7800 wireless bridge in the same application was superb with consistently low latency. Unifi can be had for cheaper second hand. Lots of corpos have them and old units get dumped upon upgrades.
- The OpenWrt One, through my very limited testing shows great performance in good radio conditions. Once you put some obstacles for the signal, performance degrades much quicker than Unifi U6 Pro. In a particular test where the Unifi achieved 50Mbps, the OpenWrt One did 1.5Mbps. I haven’t compared it to an R7800. I don’t know if it would perform any better with different antennas.
Before that I’ve used R7000, WZR-300HP, WL-500g, WRT54G/L, among others, but none of these are relevant today. :D
Unifi has amazing radio performance, but the software is yucky. and they “recently” (last year?) had a backwards-incompatible update of the controller software which I still didn’t get to migrate.
I’m probably on it already on account that my docker service pulls the latest image on restart. Something I should change.
GL.Inet. OpenWRT at the core, and a solid hardware base to run on.
I love that GL.iNet stuff ships with OpenWRT (or apparently FreeRTOS in the case of the Thread border router I’m eyeing right now), but I wish they would make stuff like ceiling or wall-mounted PoE access points and rack-mountable wired routers. The form-factor is what stops me from choosing them over TP-Link devices that I have to flash OpenWRT onto myself.
2nd hand Ruckus.
They’re decent quality that you’d see in a commercial / enterprise setting (so PoE), but Ruckus also have their “Unleashed” firmware which removes the need for a WLC.
I have 2 in a mesh at home and easily support many IoT devices, phones, laptops, etc on multiple SSIDs
