• 0 Posts
  • 3 Comments
Joined 1 year ago
cake
Cake day: August 9th, 2023

help-circle
  • In order for MS and Apple/ios to block people from booting linux on “their” machines, they came up with the secure-boot scheme. Commercial puppets and traitors of open free software rushed to be part of the scheme so all the rest of the linux distributions couldn’t boot but their systems could.

    Now we are accused of being elitists and not alarm new users of true garbage distributions?

    If anyone is stuck trying to disable secure-boot and couldn’t it is their own damn fault for buying garbage machines. Gigabyte (not Gigabit) has created some monstrosities of bios software that look like a video game and it is hard to count in how many places you have to disable the crap in order to boot open and free linux.


  • Battery: dead --> 2 senarios 1 Battery shows the right voltage but can’t retain much charge, the voltage drops right away with a small load. 2 Battery can still have capacity to be charged but never reaches the required voltage.

    In both cases, 2 separate reasons for battery problem, the battery is useless for what is needed.


  • If a battery is rated at 4amph and it is 99% discharged (dead), and it takes 4hr to fully charge then it is charging at 1amp/h, at 2amph it would charge in 2hrs. Why do you actually want to know the number of Amps passing through? It may further confuse you if you read your charger is rated at 2amph and is only charging at 1.7amps

    2amps at 5V = 10W, and 4amph of 4.4V = 17…6Wh

    acpi vattery battctl can all provide some relevant info, but basically it is simple formulas of volt x amp x time = power/Wh measurements. The software may actually confuse you more as things in charging, discharginj and rates are not very linear and understood outside physics and practical electronics.

    For example, some software will tell you your battery is at 0, when in fact the battery may be 18% charged. A battery for example rated at 4.4V may actually show 4.6 when fully charged, When it begins to fall off given the load it is presented by the machine, the voltage may drop below a threshold the manufacturer considers safe, say 4.1V, and therefor the machine shuts down.

    Take the battery out and measure it and it shows 4.38V but give it a load, say a small 4-5V light bulb (a resistance) and it drops to 4.05V. Plug the charger on and measure it, it shows 5.0V Weird? No, this is how it works, car, motorcycle, e-bike, laptop or vaper. A 12V battery for a car that unplugged shows 12V, it is nearly dead. A tiny moped battery may show 12.6V, if you try to crank a V8 engiine with it will drop to 0.4V and it would stilll be pretty well charged, for the moped. A 12.3V from a boat may crank that V8 car engine like when it was new. + You have a large tank of 200lit and at the bottom through a pipe you measure 5psi, you have a little tank with 4.1psi, you connect them and there is flow, till the flow stops from the large tank to the little one and both have 4.6psi, no flow. Exchange psi for V and this is what a charger does. Take 5 lit off of the large tank, it still shows 4.59V, take the same from the little tank and it drops to 3.9V/psi. A boat 100amph battery can charge many 4.4V batteries at little loss, and the transfer works just like tanks equalizing each other through pressure in the transfer pipe.

    Practical:

    If a battery shows as fully charging at very little time and lasts very little time is either on a machine with a short or the battery is dead. Fast charging is never as good as slow low rate charging, because: Fast charging tends to heat up the battery, when the battery gets hot it gives a false reading of higher voltage telling the charger it is full, when if you let it cool, it may take more charge. Trickle charging is best, charge, pause, recharge, pause, recharge, at lower rates keeping the battery cool.